Basin installation in Exeter
Professional basin installation services in Exeter and surrounding areas. Local, reliable handyman - no job too small.
Price Guide
£110-£210
Typical Duration
2-4 hrs
Location
Exeter, Devon
Professional basin installation with proper connections and clean pipework. I fit your new basin securely, connect everything leak-free, and leave your bathroom tidy and working perfectly.
More Than Just Plumbing In A Basin
A properly fitted basin means years of trouble-free use. Bodged installation means leaks under the floor, loose basins wobbling about, and water damage you don't discover until it's expensive.
💡 Pro tip: Wall-hung basins need solid fixing - if your wall's plasterboard, I'll find the studs or fit a spreader board. No basin should move when you lean on it.
What Good Installation Looks Like
The difference between proper fitting and cheap work shows up fast:
| ✅ Done Right | ❌ Done Wrong |
|---|---|
| Basin rock-solid on wall or pedestal | Wobbles, moves when touched |
| Clean compression joints, no leaks | Drips from push-fit connectors |
| Waste flows freely, proper fall | Slow drainage, standing water |
| Taps fitted level and secure | Wonky taps, loose grub screws |
| Sealant neat and minimal | Blobbed silicone everywhere |
What You Get
🔧 The Full Service
| Stage | What Happens |
|---|---|
| Remove | Old basin disconnected, pipework capped off safely |
| Prepare | Wall checked, fixings positioned, pipework adjusted |
| Fit | Basin secured properly, taps fitted, waste connected |
| Test | Everything checked for leaks, drainage tested |
📦 You're Left With
- Basin fitted securely (wall-hung or pedestal)
- Hot and cold supplies connected properly
- Waste flowing freely to drain
- Neat sealant around edges
- All rubbish cleared away
Pricing Guide
| Job Type | Estimated Time | You'll Pay |
|---|---|---|
| Simple basin swap (like-for-like) | 2-2.5 hrs | £110-£135 |
| Basin swap with pipework adjustments | 2.5-3 hrs | £135-£160 |
| Full new installation (new pipework) | 3-4 hrs | £160-£210 |
Based on £60 minimum (first hour) + £50/hr after. Includes standard waste kit and connectors.
Perfect For Your Project If...
✅ Upgrading bathroom - modern basin to replace old style
✅ Wall-hung basins - need proper fixing to solid walls
✅ Different tap holes - your new basin doesn't match the old setup
✅ Cloakroom sinks - compact basins in tight spaces
Why Choose Us for Basin installation in Exeter?
Leak-free connections guaranteed
Clean, tidy pipework installation
Works with your existing plumbing where possible
Advice on basin choice if you haven't bought yet
What to Expect
Step 1: Disconnect & Remove
If you've got an old basin coming out, I disconnect the taps and waste, then remove it. Pipework gets capped off safely so nothing leaks.
Step 2: Prepare & Position
I check the wall's solid enough, mark fixing positions, and adjust pipework to match your new basin. Wall-hung basins get proper fixings into blockwork or studs.
Step 3: Fit & Connect
Basin goes up securely, taps get fitted and connected to your supplies, waste gets connected with proper fall. Everything's tightened properly - no hand-tight bodges.
Step 4: Test & Seal
I run water through hot and cold, check every connection for leaks, test the waste drains freely. Then neat sealant where basin meets wall, clean up, job done.
🔧 DIY Tips
Want to fit your own basin? Here's the reality check:
🔧 Tools you'll need
- Adjustable spanners (at least two)
- Basin wrench (for tight spaces under basin)
- Spirit level
- Drill and masonry bits (for wall-hung)
- PTFE tape and silicone sealant
- Bucket and cloths
💧 The hardest parts
- Getting tap connectors tight - awkward angle, limited space, need proper torque
- Aligning waste - must have fall but also reach the drain outlet
- Wall fixings - need to be solid, finding studs in plasterboard is critical
- No leaks - compression fittings need correct pressure, not overtightened
⚠️ Common DIY mistakes
- Overtightening connectors (cracks compression olives)
- Wall fixings not strong enough (basin pulls out)
- Waste trap too shallow (no water seal, smells)
- Forgetting isolation valves (can't service taps without turning water off)
💡 Pro trick: When fitting taps through the basin, put a blob of silicone under the tap base before tightening. Stops water creeping under and creating crud buildup.
When to call a pro: If you've got a wall-hung basin or need pipework moving, get someone in. Water damage from a leak is expensive - much more than the fitting cost.
Rather leave it to a pro? No problem - that's what I'm here for. Give me a call.
Good to Know
🎨 Bathroom renovation? Fit the basin after tiling but before decorating. That way tiles are behind the basin (looks clean), and painters can touch up any marks afterwards.
Replacing a pedestal basin with wall-hung? You'll have an outline on the floor tiles where the pedestal was. Consider this before ordering - might want to stick with pedestal style unless you're re-tiling.
Old houses with lead or iron pipes? No problem - I deal with them regularly in Exeter's Victorian and Edwardian houses. Might need different fittings but it all connects up fine.
Already got a basin? Check you've got the waste kit (trap and plug) and flexible tap connectors. Often these aren't included. I carry spares but specific finishes (chrome, brushed steel) I might need to collect.
Frequently Asked Questions
What's involved in fitting a new basin?
I fit the basin to the wall or pedestal, connect up the hot and cold supplies, fit your chosen taps, and connect the waste to the drain. Everything's tested for leaks before I leave. If your old basin's coming out first, I disconnect and remove that too.
Can you fit a basin in my older Exeter house?
Absolutely - older houses are no problem. The pipework might be different (compression fittings rather than push-fit), and walls can be wonky, but that's normal. I adjust the fitting to work with what you've got.
Do I need to buy the basin and taps myself?
Either way works. If you've already bought it, great - just make sure you've got the waste kit and tap connectors too. If not, I can advise on what'll work in your space and what holes you need for your taps.
How long does basin installation take?
Straightforward swap is usually 2-3 hours. If I'm also running new pipework, adjusting heights, or dealing with awkward access under floors, it can be 3-4 hours. I'll give you a better estimate once I've seen your setup.
Will my bathroom be usable afterwards?
Yes - water's back on as soon as I'm done, and the basin's ready to use immediately. I test everything thoroughly before leaving. You'll just need to wait for any sealant to cure fully (usually 24 hours) before heavy water exposure.
Basin installation Also Available In:
Get a Free Quote in Exeter
Call us today for a free, no-obligation quote for your basin installation job in Exeter.
01392 964094Request Online QuoteOur Rates
Got multiple jobs?
Make the most of your first hour - I can often tackle several small tasks in one visit. List everything you need done when you call!
Why Trust Us
Need Basin installation in Exeter?
Get a free quote for your basin installation job in Exeter today.